Seller Seller Ratings Info Go to Store
www.rheemheatpumpsale.com Trusted Seller In Stock New Go to Store
www.splitairsystem.com Trusted Seller In Stock New Go to Store
www.heating-air-conditioners.com Trusted Seller In Stock New Go to Store
www.house-air-conditioners.com Trusted Seller In Stock New Go to Store
www.airconditionerunitprices.com Trusted Seller In Stock New Go to Store

Note: Your submitted review is subject to the license terms set out in our Terms of Use. By submitting your review, you acknowledge that you have the authority to do so and that your review does not violate another party's copyright or intellectual property rights

Product Details
Name Rheem RH1P2417STANAA - RH1P- Series, 2 Ton, R-410A, Single Stage, Aluminum Air Handler, PSC Motor, 115V, 1 Ph, 60 Hz
Brand Rheem
Item Number RH1P2417STANAA
Manufacturer Product Number RH1P2417STANAA
SKU - PIM Number 1399041970735
ERP Number 349371
UPC 662021359316
Unit of Measure EACH
Weight 90.0 Pound (lb.)
Length 21.7 Inches (in)
Width 17.5 Inches (in)
Height 42.5 Inches (in)
Hazardous Material No
EPA Cert Required No
Country of Origin MEX
Equipment Type Heat Pump
Stage Single
SEER 15.0
Refrigerant R-410a
CFM 600-800
Cooling Capacity 18000-24000
Air Flow Convertible
Voltage 115 VAC
Phase Single
Cycle/Hertz 60
Minimum Circuit Amps 5
Maximum Fuse Size 15
Blower Motor HP 1/5 HP
Filter Size 16" x 20"
RPM 1075
Suction Line Size 3/4"
Motor Type PSC
Liquid Line Size 3/8"
Certifications AHRI, ISO 9001:2008
Color Gray
Energy Star Rated No
LEED Certified No
UL Listed Yes
UL Recognized No
Tonnage 2
Tier Standard Efficiency
Product Family RH1P
GEM - Case Quantity


Rheem Standard Efficiency Air Handler RH1P- Series

Features:
  • The most compact unit design available, all standard heat air handler models only 42 1/2 to 55 1/2 inches [1079 to 1409 mm] high.
  • Attractive pre-painted cabinet exterior.
  • Rugged wall steel cabinet construction, designed for added strength and versatility.
  • 1.0" foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance.
  • Four leg blower motor mount.
  • Blower housing with controls, motor and blower. Slide out design for service and maintenance convenience.
  • Traditional open wire element design for heat applications.
  • Field convertible for vertical Downflow, horizontal left hand or right hand air supply.
  • 3 combustible floor base accessories fit all model sizes when required for Downflow installations on combustible floors.
  • Indoor coil design provides low air side pressure drop, high performance and extremely compact size.
  • Expansion valve on indoor coil provides for operation with air conditioning.
  • Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing.
  • Coils are tested at the factory with an extensive refrigerant leak check.
  • Coils have copper sweat refrigerant connections.
  • Coils utilize Chatleff metering device connections.
  • Molded polymer corrosion resistant condensate drain pan is provided on all indoor coils.
  • Supply duct flanges provided as standard on air handler cabinet.
  • Provisions for field electrical, connections available from either side or top of the air handler cabinet.
  • Connection point for high voltage wiring is inside the air handler cabinet. Low voltage connection is made on the outside of the air handler cabinet.
  • Concentric knockouts are provided for power connection to cabinet. Installer may pull desired hole size up to 2 inches [51 mm] for 1 1/2 inch [38 mm] conduit.
  • Front refrigerant and drain connections.